EndoGear3 Ordering Information Telemetry ENDOGEAR BASE STATION

Telemetry
EndoGear3 Ordering Information
ENDOGEAR® BASE STATION
A complete EndoGear® system consists of a Base
Station, one or more Remote Transceivers and an
Implant. The Implant requires a Battery Power
Module and a combination of Velocity, Pressure
or ECG Sensors. There may be up to 2 channels of
Velocity and 2 channels combined of Pressure and
ECG. The RF frequency band of the Implant must
match the Transceiver.
EG108
REMOTE TRANSCEIVERS
REGION
MONOPOLE
PLANAR
FREQUENCY BAND
Japan
EG-RM-M22
EG-RP-M22
200 - 399 MHz
US, CA, EU, NZ,
AU, CHN
EG-RM-M23
EG-RP-M23
400 - 599 MHz
US, CA, EU, NZ,
AU, CHN, JP
EG-RM-M25
EG-RP-M25
800 - 999 MHz
ENDOGEAR® IMPLANT
Catalog #: EG3 - V
TRANSCEIVER SPLITTERS*
EG-RTS-M22
Expands Transceiver Range
EG-RTS-M23
EG-RTS-M25
# Biometric
Channels (0-2)
DOPPLER FLOW VELOCITY PROBES
EG-VPB0.7-x
EPIVASCULAR
EG-VV-x
EG-VPB1.0-x
ENDOVASCULAR
COMBINED
ENDOVASCULAR
& PRESSURE
EG-VE1-x
(size: 1F)
EG-VEPR1-x
(size: 1F)
EG-VE3-x
(size: 3F)
EG-VEPR3-x
(size: 3F)
Built-in Temperature
RF Frequency
Band to Match
Transceiver (M2x)
PRESSURE SENSORS (BIOMETRIC)
EG-VPB1.5-x
CATALOG #
EG-VPB2.0-x
EG-VPB2.5-x
EG-VPB3.0-x
EG-VPB3.5-x
CATHETER SIZE
LENGTH (CM)
EG-SPS1-x
1F
specify
EG-SPS3-x
3F
specify
ECG SENSORS (BIOMETRIC)
For all, specify cable length in cm.
EG-VPB4.0-x
T - M2
# Velocity
Channels (0-2)
EndoGear®
Series
*Match to Transceiver Frequency Band (M2x)
PERIVASCULAR
S
EG-SC2-x
EG-VPB5.0-x
(small gauge ECG leads, specify length)
EG-VPB6.0-x
EG-VPB7.0-x
EG-VPB8.0-x
BATTERY POWER MODULES
VOLUME
(CC)
CAPACITY
(AMP HRS)
CABLE
LENGTH (CM)
BATTERY
SIZE
ESTIMATED HOURS OF
CONTINUOUS USE
EG3-P4CP-1.2
4
1.2
5
1/2 AA
100 - 150*
EG3-P10CP-2.4
10
2.4
5
AA
200*
EG3-P15CP-3.6
15
3.6
5
A
300*
CATALOG #
* Dependent on configuration.
THROUGH-SKIN POWER OPTIONS
EG3-WPR (Wireless power receiver for EG3 Implant)
EG3-WPS (Wireless power supply for rodent cage)
EG-3-ds Rev. A 4/14
EG3 Implant with
antenna, perivascular
probe, pressure
sensor, ECG, and
wireless power
receiver
EndoGear3 Signals & Component Specifications
SYSTEM SIGNALS
IMPLANT (EG3-VxSxT-M2x)
Flow Velocity Channels: Configurable; up to 2
Case Volume (without connectors):
Biometric Sensor Channels: Configurable; up to 2
• 3.5 cc; 28 mm L x 30 mm W x 9 mm D
Temperature Channel: 1 Sensor embedded in Implant
Weight: 8 grams
Reference Barometric Pressure: 1 in Base Station
Power Consumption (maximum configuration):
Signal Sampling Rate (all channels): 200 Samples/sec
• Sleep: 1.8 mAmp
DOPPLER FLOWMETER
Ultrasound Frequency: 20 MHz
Pulse Repetition Frequency: 64 kHz maximum
Range Gate Adjustment Limits: 0.7 - 8 mm in
0.7 mm increments
Doppler Frequency Shift Measured: ± 20 kHz
Blood Velocity Range: ± 120 cm/sec.
Perivascular Cuff Probes: 0.7 - 8 mm vessel diameter
Piezoelectric Doppler Transducer: 1 mm diameter
BLOOD PRESSURE
Range: -50 to +300 mmHg
Intravascular Pressure Sensor:
• On: 11 mAmp
Battery Power Module: Lithium-thionyl chloride; sizes
A: 3.6V, AA: 2.4V or 1/2AA: 1.2V (disposable, nonrechargeable)
Wireless Power Supply & Receiver: No battery
needed. Induction coil attached to Implant.
BASE STATION
Dimensions: 10.75” L x 10” W x 3.2” D
Weight: 4 lbs.
Electrical Power: 9 VDC
Analog Output Signal Range: 0 - 5 volts; all channels
Storage Temperature: -10 to +60°C; ≤ 90% humidity
Operational Temperature: 0 - 40°C
• 1 French (0.3 mm dia)
RF TRANSCEIVER
• 3 French (1 mm dia)
Multichannel RF Bands (country specific):
ECG
Input Impedance: ≥ 10 MΩ
Signal Band: 0.5 - 50 Hz
• M22: 200 - 399 MHz
• M23: 400 - 599 MHz
• M25: 800 - 999 MHz
Range (environmental dependent):
TEMPERATURE
• Monopole: 3 - 6 meters; 1 meter challenged
Temperature Range: 15 - 50°C
• Planar: 1 - 3 meters; 20 - 50 cm minimum
Resolution: 0.0625°C
Base Station and
Transceiver
Wireless power supply
for rodent cage
www.transonic.com