Physics 231 Topic 13: Heat Wade Fisher Nov 19-28 2012

Physics 231
Topic 13: Heat
Wade Fisher
Nov
19-28
2012
MSU Physics
231 Fall
2012
1
Clicker Quiz!
What happens to the volume
of a balloon if you put it in the
freezer?
a) it increases
b) it does not change
c) it decreases
MSU Physics 231 Fall 2012
2
Key Concepts: Heat
Heat and Thermal Energy
Heat & its units
Heat Capacity & Specific Heat
Thermal Equilibrium
Equipartition theorem
Phase Changes
Latent heat of fusion, vaporization
Conduction, Convection, and Radiation
Thermal Conductivity
Stefan-Boltzman law
Covers chapter 13 in Rex & Wolfson
MSU Physics 231 Fall 2012
3
Internal Energy
In chapter 12: The internal (total) energy for an ideal
gas is the total kinetic energy of the atoms/particles
in a gas.
For a non-ideal gas: the internal energy is due to kinetic
and potential energy associated with:
• translational motion
• rotational motion
• vibrational motion
• intermolecular potential energy
|PEideal gas=0| < |PEnon-ideal gas| < |PEliquid| < |PEsolid|
PE
PE: negative!
MSU Physics 231 Fall 2012
R
4
Heat
Heat: The transfer of thermal energy between objects
because their temperatures are different.
Heat: energy transfer
Symbol: Q
Units: Calorie (cal) or Joule (J)
1 cal = 4.186 J (energy needed to raise
1g of water by 10C)
MSU Physics 231 Fall 2012
5
Heat transfer to an object
The amount of energy transfer Q to an object with mass m
when its temperature is raised by T:
Q = cmT
Change in
temperature
Energy transfer
(J or cal)
Mass of object
Specific heat
(J/(kgoC) or cal/(goC)
MSU Physics 231 Fall 2012
6
Example
Substance
Specific Heat Specific Heat
J/kg oC
cal/g oC
aluminum
900
0.215
copper
387
0.092
water
4186
1.00
A 1 kg block of Copper is
raised in temperature by
10oC. What was the heat
transfer Q.?
MSU Physics 231 Fall 2012
7
Another one
A block of Copper is dropped from a height of 10 m.
Assuming that all the potential energy is transferred into
internal energy (heat) when it hits the ground, what is the
raise in temperature of the block (ccopper=387 J/(kgoC))?
MSU Physics 231 Fall 2012
8
Calorimetry
If we connect two objects with different temperature
energy will transferred from the hotter to the cooler
one until their temperatures are the same.
If the system is isolated:
Qcold=-Qhot
mcoldccold(Tfinal-Tcold)=-mhotchot(Tfinal-Thot)
the final temperature is: Tfinal=
mcoldccoldTcold+mhotchotThot
MSU Physics 231 Fall 2012
mcoldccold+mhotchot
9
Clicker Question!
A block of iron that has been heated to 1000C is dropped
in a glass of water at room temperature (200C).
After the temperatures in the block and the water
have become equal:
a) The water has changed more in temperature than the
iron block.
b) The water has changed less in temperature than the
iron block
c) the temperatures of both have changed equally
d) I need more info to say anything!
MSU Physics 231 Fall 2012
10
Heating Water with a Ball of Lead
A ball of Lead at T=100oC with mass 300 g is dropped in a
glass of water (0.3 L) at T=200C. What is the final
(after thermal equilibrium has occurred) temperature of
the system? (cwater=1 cal/goC, clead=0.03 cal/goC water=103kg/m3)
MSU Physics 231 Fall 2012
11
An Example
The contents of a can of soda (0.33 kg) which
is cooled to 4oC is poured into a glass (0.1 kg) that is at
room temperature (200C). What will the temperature
of the filled glass be after it has reached full equilibrium
(glass and liquid have the same temperature)?
Given cwater=4186 J/(kgoC) and cglass=837 J/(kg0C)
MSU Physics 231 Fall 2012
12
And another
A block of unknown substance with a mass of 8 kg, initially
at T=280K is thermally connect to a block of copper (5 kg)
that is at T=320 K (ccopper=0.093 cal/g0C). After the system
has reached thermal equilibrium the temperature T equals
290K. What is the specific heat of the unknown material
in cal/goC?
copper
????
MSU Physics 231 Fall 2012
13
Mixing 3 liquids
Three different liquids are mixed together in a calorimeter.
The masses, specific heats and initial temperatures of the liquids are:
T1 = 24.5 °C,
m1 = 475 g,
c1 = 225 J/kgC,
T2 = 53.5 °C,
m2 = 355 g,
c2 = 500 J/kgC,
T3 = 81.5 °C.
m3 = 795 g.
c3 = 840 J/kgC.
What will be the temperature of the mixture in Celsius?
MSU Physics 231 Fall 2012
14
Phase Change
GAS(high T)
Q=cgasmT
Gas 
liquid
Q=csolidmT Solid (low T)
liquid (medium T)
liquid 
solid
Q=cliquidmT
MSU Physics 231 Fall 2012
15
Gas 
liquid
Phase change
When heat is added to a liquid, potential energy goes to 0
(the energy stored in the stickiness of the liquid is taken away)
DURING THE CHANGE FROM LIQUID TO GAS, THE KINETIC
ENERGY DOES NOT CHANGE AND SO THE TEMPERATURE
DOES NOT CHANGE.
ALL ADDED HEAT GOES TO CHANGING PE
When heat is taken from a gas, potential energy goes to the
stickiness of the fluid
DURING THE CHANGE FROM GAS TO LIQUID, THE KINETIC
ENERGY DOES NOT CHANGE AND SO THE TEMPERATURE
DOES NOT CHANGE.
ALL REMOVED HEAT GOES TO CHANGING PE
MSU Physics 231 Fall 2012
16
liquid
solid
Phase change
When heat is added to a solid to make a liquid, potential energy in
the bonds between the atoms become less
DURING THE CHANGE FROM SOLID TO LIQUID, THE KINETIC
ENERGY DOES NOT CHANGE AND SO THE TEMPERATURE
DOES NOT CHANGE.
ALL ADDED HEAT GOES TO CHANGING PE
When heat is taken from a liquid, the bonds between atoms
becomes stronger (potential energy is more negative)
DURING THE CHANGE FROM LIQUID TO SOLID, THE KINETIC
ENERGY DOES NOT CHANGE AND SO THE TEMPERATURE
DOES NOT CHANGE.
ALL REMOVED HEAT GOES TO CHANGING PE
MSU Physics 231 Fall 2012
17
Clicker Question
Which of the following is not true?
a) During a phase transformation, the temperature of
a material remains unchanged
b) During a phase transformation, the kinetic energy of
the material remains unchanged
c) During a phase transformation, the potential energy
of the material is unchanged
d) During a phase transformation, the total energy of
the material changes
MSU Physics 231 Fall 2012
18
Okay, the Temperature does not
change in a phase transition!
But what is the amount of heat added
to make the phase transition?
Gas 
liquid
Qgasliquid=-MLv
Qliquidgas=+MLv
M:mass
Lv=latent heat of vaporization (J/kg or cal/g)
depends on material.
Use the table in the book for LON-CAPA
MSU Physics 231 Fall 2012
19
solid 
liquid
Qliquidsolid=-MLf
Qsolidliquid=+MLf
M:mass
Lf=latent heat of fusion (J/kg or cal/g)
depends on material.
Use the table in the book for LON-CAPA
MSU Physics 231 Fall 2012
20
Phase Change
GAS(high T) Q=cgasmT
Gas 
liquid
Q=mLv
Q=csolidmT Solid (low T)
liquid (medium T)
Q=cliquidmT
MSU Physics 231 Fall 2012
liquid 
solid
Q=mLf
21
Clicker Question!
Ice is heated steadily and becomes liquid and then vapor.
During this process:
a) the temperature rises continuously.
b) when the ice turns into water, the temperature
drops for a brief moment.
c) the temperature is constant during the phase
transformations
d) the temperature cannot exceed 100oC
MSU Physics 231 Fall 2012
22
ice
water
0
ice+water
steam
T (oC)
water+steam
100
THE PHASE TRANSFORMATIONS OF WATER
MSU Physics 231 Fall 2012
23
water
ice
steam
0
ice+water
T (oC)
water+steam
100
Ice with T=-30oC is heated
to steam of T=1500C.
How much heat (in cal) has
been added in total?
cice=0.5 cal/goC
cwater=1.0 cal/goC
csteam=0.480 cal/goC
Lf=540 cal/g
Lv=79.7 cal/g
m=1 kg=1000g
MSU Physics 231 Fall 2012
24
A Question
A block of gold (room temperature 200C)
is found to just melt completely after
supplying 4x103 J of heat. What
was the mass of the gold block?
Given: Lf=6.44x104 J/kg Tmelt=1063oC cspecific=129 J/kg0C
a)
b)
c)
d)
e)
0.01 kg
0.02 kg
0.03 kg
0.06 kg
10 kg
MSU Physics 231 Fall 2012
25
How can heat be transferred?
MSU Physics 231 Fall 2012
26
Conduction
Touching different materials: Some feel cold, others
feel warm, but all are at the same temperature…
MSU Physics 231 Fall 2012
27
Thermal conductivity
metal
T=200C
wood
T=200C
The heat transfer
in the metal is
much faster than
in the wood:
(thermal
conductivity)
T=370C
MSU Physics 231 Fall 2012
T=370C
28
Heat transfer via conduction
Tc
Th
Conduction occurs if there is a
temperature difference between
two parts of a conducting medium
Rate of energy transfer P
A
P = Q/t (unit Watt)
P = kA(Th-Tc)/x = kAT/x
k: thermal conductivity
Unit:J/(msoC)
x
Metals
Gases
Nonmetals
MSU Physics 231 Fall 2012
k~300 J/(msoC)
k~0.1 J/(msoC)
k~1
J/(msoC)
29
Th
Tc
A
Example
A glass window (A=4m2,x=0.5cm)
separates a living room (T=200C)
from the outside (T=0oC). A) What
is the rate of heat transfer through
the window (kglass=0.84 J/(msoC))?
B) By what fraction does it change
if the surface becomes 2x smaller
and the temperature drops to -200C?
x
MSU Physics 231 Fall 2012
30
Another one.
An insulated gold wire (I.e. no heat lost to the air) is at
one end connected to a heat reservoir (T=1000C) and at the
other end connected to a heat sink (T=200C). If its length
is 1m and P=200W what is its cross section (A)?
MSU Physics 231 Fall 2012
31
Water 0.5L
1000C
And another
A=0.03m2 thickness: 0.5cm.
1500C
A student working for his exam feels hungry and starts boiling
water (0.5L) for some noodles. He leaves the kitchen when
the water just boils.The stove’s temperature is 1500C.
The pan’s bottom has dimensions given above. Working hard
on the exam, he only comes back after half an hour. Is there
still water in the pan? (Lv=540 cal/g, kpan=1 cal/(ms0C)
MSU Physics 231 Fall 2012
32
Clicker Quiz!
Given your experience of what
feels colder when you walk on it,
a)
a rug
which of the surfaces would
b)
a steel surface
have the highest thermal
c)
a concrete floor
conductivity?
d)
MSU Physics 231 Fall 2012
has nothing to do with
thermal conductivity
33
Multiple Layers
Th k
1
Tc
k2
A
L1
Q A(Th  Tc )
P

t  ( Li / ki )
i
L2
MSU Physics 231 Fall 2012
34
Q A(Th  Tc )
P

t  ( Li / ki )
i
inside
Insulation
Th
Tc
L1 L2 L3
A house is built with 10cm thick wooden walls and roofs.
The owner decides to install insulation. After installation
the walls and roof are 4cm wood+2cm insulation+4cm wood.
If kwood=0.10 J/(ms0C) and kisolation=0.02 J/(ms0C), by what
factor does he reduce his heating bill?
MSU Physics 231 Fall 2012
35
Convection
T high
 low
MSU Physics 231 Fall 2012
36
Radiation
Nearly all objects emit energy through radiation:
P=AeT4 : Stefan’s law (J/s)
=5.6696x10-8 W/m2K4
A: surface area
e: object dependent constant emissivity (0-1)
T: temperature (K)
P: energy radiated per second.
MSU Physics 231 Fall 2012
37
emissivity
Ideal reflector
e=0
no energy is absorbed
Ideal absorber (black body)
e=1
all energy is absorbed
also ideal radiator!
MSU Physics 231 Fall 2012
38
MSU Physics 231 Fall 2012
39
Black body
A black body is an object that absorbs all electromagnetic radiation
that falls onto it. They emit radiation, depending on their temperature.
If T<700 K, almost no visible light is produced (hence a ‘black’ body).
The energy emitted from a black body: P=T4 with =5.67x10-8 W/m2K4
b=2.8977685(51)×10−3 mK
Wiens displacement constant
More in PHY232!
MSU Physics 231 Fall 2012
40
Infrared Radiation
The human body emits radiation in the infrared.
With a body temperature of T=(273+37 K) = 310 K
the wavelength of the thermal emission is ~5E-5 m
MSU Physics 231 Fall 2012
41
A BBQ
The coals in a BBQ cover an area of 0.25m2. If the
emissivity of the burning coal is 0.95 and their
temperature 5000C, how much energy is radiated every
minute?
MSU Physics 231 Fall 2012
42
Net Power Radiated
If an object would only emit radiation it would eventually
have 0 K temperature. In reality, an object emits AND
receives radiation.
PNET = Ae (T4-T04)
where
T: temperature of object
T0: temperature of surroundings.
MSU Physics 231 Fall 2012
43
Example
The temperature of the human body is 370C. If the
room temperature is 200C, how much heat is given
off by the human body to the room in one minute?
Assume that the emissivity of the human body is 0.9
and the surface area is 2 m2.
MSU Physics 231 Fall 2012
44
For Next Week
Chapter 14:
The Laws of Thermodynamics
Homework Set 11 Due 11/28
Covers Chapter 13
MSU Physics 231 Fall 2012
45