GENERAL NOTES:

GENERAL NOTES:
This Standard is only applicable to the current FDOT inventory of temporary bridge components
STORAGE FACILITY:
which are manufactured in accordance with Acrow Series 300, Double Wide design. See the
Contact
associated Instructions for Design Standards (IDS) for more information.
FDOT Statewide Aluminum Shop
2590 Camp Rd.
Work this Standard with Index Nos. 21610, 21620 and 21630.
Oviedo, Fl.
407-977-6520
STRUCTURAL STEEL:
For shipping weights and dimensions of Temporary Bridge elements.
Steel Plates and Rolled Sections shall be ASTM A 709 Grade 36.
Pipe piles shall be ASTM A 252 Grade 2, Fy = 35 ksi.
SHIPPING WEIGHTS AND DIMENSIONS:
BOLTS, LAG SCREWS AND THREADED BOLT STOCK:
Decking Sizes:
Furnish high strength bolts in accordance with ASTM A325. Furnish Threaded
Stock in accordance with ASTM A36. Furnish Lag Screws in accordance with ASTM A307.
Type
Length
Width
Furnish steel washers and nuts compatible with Bolts, Threaded Stock and Lag Screws.
Curb
5’
6’-9"
800
Curb
10’
6’-9"
1420
Curb
15’
6’-9"
2200
Curb
20’
6’-9"
2800
NonCurb
5’
5’-3"
650
NonCurb
10’
5’-3"
1000
NonCurb
15’
5’-3"
1600
NonCurb
20’
5’-3"
2100
TIMBER AND LAGGING:
Timber and Lagging shall be No. 1 Southern Yellow Pine.
BACKWALL BENT PILES:
Timber Piles:
10’ Minimum Embedment into compacted backfill or into soil having a blow count greater than 6 (N>6).
Weight (lbs.)
Ultimate Capacity greater than 18 tons.
Splices are not allowed on any timber piles.
Shipping weights and dimensions of other bridge components can be
referenced in "Acrow Panel Bridging, Series 300, Technical Handbook".
H-Piles:
12’ Minimum Embedment into compacted backfill or into soil having a
PAYMENT:
blow count greater than 6 (N>6).
Temporary Detour Bridge is to be paid for under Contract Unit Price for
Ultimate Capacity greater than 18 tons.
Special Detour. If a temporary bridge system other than that shown herein
is used, the Contractor is responsible for renting or purchasing their own system.
Shims admissible between backwall pile and cap.
C:
\d\projects\standards\structures\2013book\21600-1of7.
dgn
Test piles are not required for backwall piles.
EXPANSION BEARINGS:
Inspect the PTFE (Teflon) layer and stainless steel plate prior to installation.
Do not use bearings that have a severely damaged or unbonded PTFE layer.
Clean PTFE of all grit and grime prior to installation.
Clean Stainless steel plate of all grit and grime prior to installation and finish to a smooth
buffed surface.
DISTRIBUTING BEAMS:
Longitudinal stops restraining the distributing beams may be lengthened or shortened to
center the distributing beam bearing on the cap beam.
The longitudinal stops are to bear on the distributing beam end frame.
EXPANSION JOINT SETTINGS:
Install the expansion joint considering the total continuous bridge length, location of
fixed bearings and ambient temperature at the time of installation, assume a 1" expansion
LAST
REVISION
01/01/11
REVISIO N
6/28/2012
1:
12:
23 PM
rd960rh
joint opening at 70 degrees F.
DESCRIPTION:
INDEX
FDOT DESIGN STANDARDS
TEMPORARY DETOUR BRIDGE
2013
GENERAL NOTES AND DETAILS
NO.
21600
SHEET
NO.
1
Shoulder Line (see Plans for width requirements, Typ.)
~
Approach Roadway
»¿ Detour B
~
Grade Beam
~
1 : 1.5 (Max.)
Retainer Angles (Typ.)
4" x 10" Laging
5’-0" Approach Span
with Filter Fabric
1 : 1.5 (Max.)
1 : 1.
5
(
M ax.
)
1 : 1.
5
»¿ Backwall
(
M ax.
)
AB5 or AB6 End Post (Typ.)
5’-0"
AB7 Bearing (Expansion
»¿ End
Bearing Shown Fixed
Ramp Span
Bearing Similar)
1
:1
.
5
(
Ma
x.
)
1
:
1
.5
(M
a
x
.)
Edge of Berm
1 : 1.
5 (
M ax.
)
1 : 1.
5 (
M ax.
)
C:
\d\projects\standards\structures\2013book\21600-2of7.
dgn
AB13 Swaybrace Standard (Typ.)
Toe of Fill Slope
rd960rh
24’-0" Clear Roadway Width
AB3 Bracing Frame (Typ.)
AB306 Transom DW (Typ.)
1:
12:
25 PM
AB1 Truss Panels (Typ.)
1’-6"
1’-6"
25’-6"
6/28/2012
TYPICAL PLAN VIEW OF DETOUR BRIDGE
LAST
REVISION
07/01/06
REVISIO N
(TIMBER PILE SHOWN, STEEL H PILES AND STEEL PIPE PILES SIMILAR)
DESCRIPTION:
INDEX
FDOT DESIGN STANDARDS
TEMPORARY DETOUR BRIDGE
2013
GENERAL NOTES AND DETAILS
NO.
21600
SHEET
NO.
2
End Span 30’-0" Min. (30’-4b »¿" to Bearing); 60’-0" Max. (
5’-0"
b »¿" to Bea
Intermediate Spans 30’-0" Min. ; 60’-0" Max.
»¿( Bearing to B
5’-0"
Ramp Span
2’-6"
»¿ Be
End Post (Typ.)
Approach Asphalt
1’
-0" 1’
-10b "
"
5
2’
-8
"–
AB13 Swaybrace
Standard (Typ.)
5’-0" Berm (Min.)
»¿3˘" (AB306 Transom DW Li
AB505C Distributing Beam
AB7 Bearing (Expansion
»¿7˘" (AB307 Transom DW He
Stop (Typ. both ends)
Bearing Shown Fixed
AB22 Distributing Beam with
Bearing Similar) (Typ.)
AB23 Distributing Beam End Frames
4" x 10" Lagging
1b (Max.)
with Filter Fabric
1
Bottom of
Truss Panel
AB306 Transom DW (Typ.)
Underside of Fixed Bearing
C:
\d\projects\standards\structures\2013book\21600-3of7.
dgn
Underside of Fixed Bearing
Grade Beam
2’
-9
"
Steel Grid Deck & Curb
Underside of Expansion Bearing
Pavement
Riding Surface
5’
-1"
AB5 or AB6
Truss Panel Depth
AB1 Truss Panels (Typ.)
"
AB3 Bracing Frame (Typ.)
"–
Begin or End Detour Bridge
3’
-7
»¿ Be
3’
-8
4b "
Underside of Expansion Bearing
2’-6"
5 " Steel Grid Deck
Approach Span
Existing Ground Line
»¿ End
»¿ Typical Intermediate
rd960rh
»¿ Backwall
1:
12:
28 PM
ELEVATION VIEW
LAST
REVISION
01/01/08
REVISIO N
6/28/2012
(TIMBER PILES SHOWN, STEEL H PILES AND STEEL PIPE PILES SIMILAR)
DESCRIPTION:
INDEX
FDOT DESIGN STANDARDS
TEMPORARY DETOUR BRIDGE
2013
GENERAL NOTES AND DETAILS
NO.
21600
SHEET
NO.
3
28’-6"
1’-6"
12’-9"
12’-9"
1’-6"
24’-0" Clear Roadway
»¿ Bear
AB3 Bracing Frame (Typ.)
»¿ Detour B
AB2 Raker Bar
AB51 Panel Pins
(Top & Bottom Typ.)
Steel Grid Deck & Curb
AB1 Truss Panels (Typ.)
AB7 Bearing
(Expansion Bearing
shown, Fixed Bearing
similar, Typ.)
AB306 Transom DW (Typ.)
AB13 Swaybrace Standard (Typ.)
AB505C Distributing
C:
\d\projects\standards\structures\2013book\21600-4of7.
dgn
Beam Stop (Typ.)
AB22 Distributing Beams with AB23
Distributing Beam End Frame (Typ.)
Timber Bent shown for illustration purposes,
See Plans for actual Bent Designs, including
Pile sizes and spacing, bent cap and bracing
requirements.
TYPICAL SECTION THRU DETOUR BRIDGE AT INTERIOR BENTS (TYPICAL SECTION AT END BENTS SIMILAR WITHOUT DISTRIBUTING BEAMS)
LAST
REVISION
07/01/06
REVISIO N
6/28/2012
1:
12:
30 PM
rd960rh
(TIMBER PILE SHOWN, STEEL H PILES AND STEEL PIPE PILE SIMILAR)
including Fixed & Expansion Bearings
»¿ Truss
»¿ Bear
FDOT suppliesTem porary Bridge Com ponents
»¿ Truss
Bearing Saddle Plates, Keeper Bars & Shim s.
12’-0"
Contractor supplied foundations com ponents, including
12’-0"
DESCRIPTION:
INDEX
FDOT DESIGN STANDARDS
TEMPORARY DETOUR BRIDGE
2013
GENERAL NOTES AND DETAILS
NO.
21600
SHEET
NO.
4
1’-0"
6"
6"
8b"
4
»¿
»¿
"
4
A
"
A
AB7 Bearing
»¿Bearing Plate ˘
AB7 Bearing
1"
2"
»¿˘" ˆ Holes (
5"
7"
5"
3"
4"
10"
1’
-2"
10"
3"
»¿ Be
5"
7"
4"
5"
»¿ Be
1"
Teflon
»¿˘" x ˘"
»¿ Truss P
»¿
2b"
2b"
»¿
B
2"
(Guide Bars Typ.)
B
»¿
A
»¿ Truss P
Stainless Steel Plate
»¿
PLAN VIEW
»¿
B
B
»¿
8b"
»¿
A
C:
\d\projects\standards\structures\2013book\21600-5of7.
dgn
AB7 Bearing
3"
PLAN VIEW
AB7 Bearing
»¿˘" x ˘"
(Guide Bars Typ.)
Stainless Steel Plate
812"
VIEW B-B
»¿Bearing Plate ˘
Teflon (Bonded
»¿
»¿to A36
VIEW B-B
AB7 Bearing
3"
AB7 Bearing
rd960rh
»¿˘" x ˘"
4" –
(Guide Bars Typ.)
1:
12:
35 PM
10"
»¿Bearing Plate ˘
6/28/2012
VIEW A-A
VIEW A-A
DETAILS FOR FDOT SUPPLIED EXPANSION BEARINGS
LAST
REVISION
01/01/10
REVISIO N
DETAILS FOR FDOT SUPPLIED FIXED BEARINGS
DESCRIPTION:
INDEX
FDOT DESIGN STANDARDS
TEMPORARY DETOUR BRIDGE
2013
GENERAL NOTES AND DETAILS
NO.
21600
SHEET
NO.
5
3" Max. (see Note)
Detour Bridge Superstructure (Truss and
Transom members shown dotted)
»¿ Truss
»¿ Distributing Beam,
1’
-4" –
Fixed Bearings
1’
-5" –
Expansion Bearings
A
AB505C Distributing Beam Stop
(Typ. both ends)
AB584 Cord Bolts
AB23 Distributing Beam
End Frame (Typ. both ends)
A
AB22 Distributing Beam
Bottom of Bearing, Top of
Bent Cap or Shim Plate
C:
\d\projects\standards\structures\2013book\21600-6of7.
dgn
8’-4"
Bent Cap & Bearing Plate shown dashed
¡ Intermediate Bent (see Note)
»¿1’-6" ( to T
»¿ Beari
ELEVATION VIEW OF DISTRIBUTING BEAM
»¿ Beari
»¿ Distributing
9"
9"
»¿ Distributing
(FIXED BEARING SHOWN, EXPANSION BEARING SIMILAR)
(Timber Intermediate Bent shown, Steel H Pile and
6b "
6b "
»¿
Steel Pipe Pile Intermediate Bents similar)
Lateral Alignment
Frame
Truss Retainer Plates
B
Dowels (Typ.)
AB505C Distributing
type vary)
Note:
»¿
Bearing may be shifted from Trus
Lateral Alignment
Bracing Bolts
Dowels (Typ.)
Bracing Bolts
»¿ as shown, Intermediate Bent may be sh
»¿ from Bearing an additional 3" to allow
pile placement tolerances.
AB23 Distributing
AB23 Distributing
Beam End Frame
rd960rh
Beam End Frame
2"
AB22 Distributing Beam
1:
12:
37 PM
shown dashed
1’-0"
1’-0"
1’
-2"
(location, number and
Distribution Beam
1’
-0" – Distribution
Truss Retainer Plates
AB505C Distributing Beam Stop
Beam End Fram e
Beam Stop (Typ.)
AB22 Distributing
Beam & Bearing
Block (Typ.)
2’-0"
B
LAST
REVISION
07/01/06
REVISIO N
6/28/2012
VIEW B-B
END VIEW A-A
DISTRIBUTING BEAM END FRAME DETAIL
DESCRIPTION:
INDEX
FDOT DESIGN STANDARDS
TEMPORARY DETOUR BRIDGE
2013
GENERAL NOTES AND DETAILS
NO.
21600
SHEET
NO.
6
28’-0"
14’-0"
14’-0"
16’-0"
12’-0"
»¿ 3 x 2 x ˘ x 10"
Grade Beam Straps (Typ.)
Rear Grade Beam Lengths
Deck Hold Down Tabs (Typ.)
1’
-7"
9b " 9b "
10" 7b "
»¿’s 5 x 5 x ˘ x
10" x 10" (Nominal)
»¿˘" ˆ
»¿2 ~ ˘" x 1’-7" x 12’-9" C
»¿ Detour B
(Typ.)
Grade Beam Timbers
7b"
9 sp. @ 1’-3" = 11’-3"
10b"
9 sp. @ 1’-3" = 11’-3"
12’-9"
10b"
12’-9"
1’-3"
»¿Spacing ˘" ˆ Holes for ˘" ˆ Lag
Cap Plate Lengths
1’-3"
25’-6"
16’-0"
12’-0"
Front Grade Beam Lengths
PLAN VIEW
12’-3"
1’-6"
1’-11"
1’-11"
2’-9"
Deck Hold Down Tabs (Typ.)
»¿ Le
12’-3"
3’-1"
1’-1"
1’-1"
3’-1"
2’-9"
1’-11"
1’-11"
1’-6"
Spacing Deck Hold Down Tabs
»¿’s 5 x 5 x ˘ x
A
»¿ 3 x 2 x ˘ x 10"
See Detail "B"
4"
»¿˘" ˆ
1’-0"
4"
Grade Beam Timbers
5’-0"
5’-0"
2’-0"
1’-0"
1’-0"
2’-0"
5’-0"
5’-0"
1’-0"
Strap Spacing
»¿?
ELEVATION VIEW
* See General Notes for setting
ANCHOR PLATE DETAIL
widths other than 70 F.
* 1" @ 70 F
»¿ 5 x 5 x ˘ x
3b"
b" x 1b" x 4" Deck Hold Down Tabs
2b"
»¿ 5 x 5 x ˘ x
Approach Asphalt
Pavement
»¿ 3 x 2 x ˘
»¿˘" x 1’-7" x 12’-9" C
Steel Grid Deck Unit
10" x 10" (Nominal)
(shown dashed)
Grade Beam Timbers
b" Anchor Plate
~
~
(placed against Grid Deck)
(shown dashed)
»¿end
3"
~
Typ. both
»
3b"
Steel Grid Deck Unit
2"
(see Detail)
1b "
C:
\d\projects\standards\structures\2013book\21600-7of7.
dgn
(Centered)
10" x 10" (Nominal)
A
Grade Beam Straps (Typ.)
»¿˘" ˆ Threaded Bar pl
b" x 5" Lag Screws (Typ.)
@ Strap locations,
3"
rd960rh
Torque to 25 Lb.-Ft.
~
»¿˘" ˆ x 6" Lag Screws (
OPTIONAL THROUGH BOLT DETAIL
(MAY BE USED IN LIEU OF STRAPS)
1:
12:
39 PM
3"
~
»¿˘" x 4" x 2’-10" ´– Strap ,
»¿bend to shape (center ˘
DETAIL "B"
holes for Lag Screws in strap)
10" x 10" (Nominal)
6/28/2012
Grade Beam Timbers
GRADE BEAM DETAILS
LAST
REVISION
07/01/06
REVISIO N
SECTION A-A
DESCRIPTION:
INDEX
FDOT DESIGN STANDARDS
TEMPORARY DETOUR BRIDGE
2013
GENERAL NOTES AND DETAILS
NO.
21600
SHEET
NO.
7